Industrial molded-fiber machinery — since 1979
GDM Industries designs and manufactures pulp molding production lines, egg-tray machines, molds and tooling for industrial producers worldwide — from compact entry lines to high-capacity automated platforms.
A standardized platform for molded-fiber production. Six models from 600 to 2,200 trays per hour, engineered around a common industrial architecture.
Machine images are shown for presentation purposes. Actual machines may differ slightly in appearance and configuration.
Capacity reference: standard 30-egg tray · reference mould module 320 × 320 mm.
From recovered paper to finished molded-fiber products, the GDM ECP production line combines pulp preparation, vacuum forming and controlled drying in one continuous process.
Recovered paper and water are mixed to create pulp.
Two primary tanks store the prepared pulp suspension.
The secondary tank feeds the molding section at a steady rate.
Fiber is vacuum-formed into molded-fiber products on product-specific moulds.
Electrical control panel that operates and monitors the line.
Supplies compressed air for the line’s pneumatic systems.
Provides the negative pressure used during molded-fiber forming.
Continuous metal dryer that removes moisture from the formed products.
Every GDM ECP line follows four controlled production stages. The sequence is the same at every capacity — the difference is scale.
Recovered paper or approved fiber is mixed with water and prepared as a stable pulp suspension.
Fiber is deposited on product-specific mesh moulds using vacuum. Process water is recovered into the closed water circuit.
Wet molded products are transferred from the forming moulds into the downstream carrier system.
Products are dried to the required moisture level and proceed to collection and downstream handling.
The ECP platform is a molded-fiber production system, not a single product machine. Product geometry is mould-specific; the platform adapts.
Bespoke molded-fiber products designed around a specific geometry and use — from industrial components to tailored packaging solutions.
Molded-fiber egg trays for the safe transport and storage of eggs — the reference product of the ECP platform, produced at every capacity level.
Molded-fiber trays for fruit, vegetables and food handling — ventilated, food-appropriate packaging produced on the ECP platform.
Custom molded-fiber inserts and protective packaging for industrial and consumer goods — engineered cushioning that replaces expanded-polystyrene and plastic inserts.
GDM production lines are built around recovered paper: with water and controlled process conditions, selected paper is prepared into pulp, formed and dried into molded-fiber products in one continuous line.
Recovered paper or approved fiber is brought into the process as the raw material.
Paper is mixed with water in the pulper and broken down into a pulp suspension.
Mixers and tanks keep the suspension consistent and feed the forming section at a steady rate.
Fiber is deposited on product-specific moulds under vacuum and dewatered; process water is recovered into the line’s water circuit.
Formed products are dried to the required moisture level and collected for downstream handling.
The same process architecture runs across the ECP range. Raw-material handling, pulp preparation and process-water recovery are configured for the project.
Every line is a balanced combination of pulp preparation, forming, drying, vacuum and control — specified together for the project.
PLC-based sequencing, an operator interface and electrical protection coordinate every stage — configured for the project's control requirements.
An insulated industrial dryer with forced hot-air circulation brings products to the required moisture level — sized for the line's production load.
Fiber is deposited on product-specific mesh moulds under vacuum, then transferred in a synchronized cycle into the downstream system.
Recovered paper or approved fiber is prepared as a stable, consistent pulp suspension — the first controlled stage of every GDM line.
Industrial machinery is measured over years, not months. GDM lines are engineered for that time horizon.
Decades of continuous design and manufacturing experience in molded-fiber production equipment.
One proven architecture across six capacity levels simplifies operation, training and spare-parts planning.
Lines, molds and process parameters are configured for the product, the site and the production target.
Industrial, serviceable construction designed to be maintained by a normal plant team.
Export experience across Türkiye, the Middle East and Africa, with documentation and commissioning support.
Start with a compact line, grow into a higher-capacity platform — the engineering approach stays consistent.
GDM production lines and equipment serve producers in an international network of markets.
Send us your target product, capacity and site conditions. We respond with the line configuration that fits.
